Raspberry Pi Compute
Jump to navigation
Jump to search
https://www.waveshare.com/wiki/Write_Image_for_Compute_Module_Boards_eMMC_version
https://www.waveshare.com/wiki/CM4-DUAL-ETH-4G/5G-BASE
https://github.com/SequentMicrosystems/ti-rpi/blob/main/README.md
Setup
Install image to Compute using imager software.
https://www.raspberrypi.com/software/
The following commands can be executed manually, or can be saved into an 'sh' file (e.g. setup.sh) and then run using bash setup.sh
sudo apt-get update sudo apt-get upgrade bash <(curl -sL https://raw.githubusercontent.com/node-red/linux-installers/master/deb/update-nodejs-and-nodered) sudo systemctl enable nodered.service
sudo apt-get -y install mosquitto sudo apt-get -y install pwgen sudo apt-get -y install wget sudo apt-get -y install zip
sudo apt-get -y install build-essential cmake echo "Installing M-Bus Libraries..." sudo apt-get -y install git libtool libltdl-dev autoconf automake sudo git clone https://github.com/rscada/libmbus.git cd libmbus sudo sh clean.sh sudo sh build.sh make sudo make install sudo ln -s /usr/local/lib/libmbus.so.0 /usr/lib/libmbus.so.0
mkdir /home/pi/node-hiu mkdir /home/pi/node-hiu/logs mkdir /home/pi/node-hiu/iHIU mkdir /home/pi/node-hiu/flows sudo chmod -R 775 /home/pi/node-hiu
cd ~ git clone https://github.com/SequentMicrosystems/ti-rpi.git cd ti-rpi/ sudo make install
cd ~ git clone https://github.com/SequentMicrosystems/megabas-rpi.git cd /home/pi/megabas-rpi sudo make install
The following nodes should be installed via the Node-RED Palette Manager. Items in bold may need manually installing.
node-red node-red-contrib-arp node-red-contrib-crypt node-red-contrib-drawsvg node-red-contrib-heatweb node-red-contrib-m-bus node-red-contrib-play-audio node-red-contrib-ui-level node-red-contrib-ui-svg node-red-dashboard node-red-node-daemon node-red-node-email node-red-node-pi-gpio node-red-node-ping node-red-node-random node-red-node-serialport node-red-node-smooth node-red-node-ui-table node-red-contrib-pid
boot.config
# For more options and information see # http://rpf.io/configtxt # Some settings may impact device functionality. See link above for details # uncomment if you get no picture on HDMI for a default "safe" mode #hdmi_safe=1 # uncomment the following to adjust overscan. Use positive numbers if console # goes off screen, and negative if there is too much border #overscan_left=16 #overscan_right=16 #overscan_top=16 #overscan_bottom=16 # uncomment to force a console size. By default it will be display's size minus # overscan. #framebuffer_width=1280 #framebuffer_height=720 # uncomment if hdmi display is not detected and composite is being output #hdmi_force_hotplug=1 # uncomment to force a specific HDMI mode (this will force VGA) #hdmi_group=1 #hdmi_mode=1 # uncomment to force a HDMI mode rather than DVI. This can make audio work in # DMT (computer monitor) modes #hdmi_drive=2 # uncomment to increase signal to HDMI, if you have interference, blanking, or # no display #config_hdmi_boost=4 # uncomment for composite PAL #sdtv_mode=2 #uncomment to overclock the arm. 700 MHz is the default. #arm_freq=800 # Uncomment some or all of these to enable the optional hardware interfaces dtparam=i2c_arm=on #dtparam=i2s=on #dtparam=spi=on # Uncomment this to enable infrared communication. #dtoverlay=gpio-ir,gpio_pin=17 #dtoverlay=gpio-ir-tx,gpio_pin=18 # Additional overlays and parameters are documented /boot/overlays/README # Enable audio (loads snd_bcm2835) dtparam=audio=on # Automatically load overlays for detected cameras camera_auto_detect=1 # Automatically load overlays for detected DSI displays display_auto_detect=1 # Enable DRM VC4 V3D driver dtoverlay=vc4-kms-v3d max_framebuffers=2 # Run in 64-bit mode arm_64bit=1 # Disable compensation for displays with overscan disable_overscan=1 [cm4] # Enable host mode on the 2711 built-in XHCI USB controller. # This line should be removed if the legacy DWC2 controller is required # (e.g. for USB device mode) or if USB support is not required. #otg_mode=1 dtoverlay=dwc2,dr_mode=host [all] [pi4] # Run as fast as firmware / board allows arm_boost=1 [all] enable_uart=1 dtoverlay=pi3-miniuart-bt dtoverlay=uart5 dtoverlay=uart4 dtoverlay=uart3 dtoverlay=uart2